THERMAL SCIENCE

International Scientific Journal

Thakur Pankaj

STEADY THERMAL STRESS AND STRAIN RATES IN A CIRCULAR CYLINDER WITH NON-HOMOGENEOUS COMPRESSIBILITY SUBJECTED TO THERMAL LOAD

ABSTRACT
The non-homogeneity is assumed due to variation of modulus of compression. It has seen that in the presence of temperature, a cylinder made of non-homogeneous material k<0 (Non-homogeneity is less at internal surface than at outer surface) require high pressure to become fully plastic as is required for initial yielding and this pressure goes on increasing with the increases in temperature, showing that a cylinder made of non-homogeneous material k<0 is on the safer side of design. For homogeneous case, it has been observed that the circumferential stress has maximum value at the external surface of the cylinder made of incompressible material as compared to compressible material. For Homogeneous case, with effects of temperature reduces the stresses at the external surface of the cylinder in comparison to pressure effects only. Strain rates are found to be maximum at the internal surface of the cylinder made of compressible material and they decrease with the radius. With the introduction of temperature effect, the creep rates have higher values at the internal surface but lesser values at the external surface as compare to a cylinder subjected to pressure only.
KEYWORDS
elastic-plastic, creep, transition, temperature, non-homogeneous, stresses, strain
PAPER SUBMITTED: 2011-03-15
PAPER REVISED: 2012-05-07
PAPER ACCEPTED: 2012-05-15
DOI REFERENCE: https://doi.org/10.2298/TSCI110315080P
CITATION EXPORT: view in browser or download as text file
THERMAL SCIENCE YEAR 2014, VOLUME 18, ISSUE Supplement, PAGES [81 - 92]
REFERENCES
[1] [1] Parkus, H., Thermo-elasticity, New York Springer-Verlag, 1976, pp. 119
[2] [2] Blazynski, T.Z., Appl. Elastico-plasticity of solids, Macmillian press Ltd. London, 1983
[3] [3] Chakrobatry, Theory of plasticity, McGraw-Hill book co., New York, 1987
[4] [4] Hill, R., Mathematical theory of plasticity, Clarendon press, Oxford, 1950
[5] [5] W. Olszak and W. Urbanowski, Elastic–plastic thick-walled non-homogeneous cylinder subjected to internal pressure and longitudinal load, AMS 7 (1955) (3), pp. 315–336
[6] [6] Ghosh, D., elastic-plastic stresses in a spherical pressure vessel of non-homogeneous material, J. Sci., engng. Res., 7 (1963), pp. 306-33
[7] [7] Mukhopadhyay, J., Effect of non-homogeneity on yiels stress in a thick walled cylinder tube under pressure , Lett. Appl. Engng. Sci., 20 (1982) , pp. 963-968
[8] [8] Seth, B. R., Measure Concept in Mechanics, Int. J. Non-linear Mech. ,I(2) (1966), pp. 35-40
[9] [9] Seth, B.R., Transition theory of elastic-plastic deformation, creep and relaxation, Nature, 195 (1962), pp. 896-897
[10] [10] Finnie, I., Heller, W.R., Creep of Engineering Material, McGraw Hill Book Co., 1952, pp. 168-86
[11] [11] Davis, e.A., Conelly, F.M., Stress distribution and plastic deformation in rotating cylinder of strain hardening material, Jr. Appl. Mech., 6 (1959), pp. 25-30
[12] [12] Rimrott, F.P.J., On the plastic behaviour of rotating cylinder, Jr. Appl. Mech., 27 (1960), pp. 309-315
[13] [13] Marin, J., Mechanical behaviour of Engineering Materials, Prentice-Hall. IOnc., Englewood Cliffs, N.J., USA, 1962, pp. 400-405
[14] [14] Dev, D., Note on the creep of a cylinder rotating about its axis, Ind. J. Maths. Mech., 3 (1965), pp. 104-107
[15] [15] Gupta S.K. and Shukla R.K., Ph.D. thesis, Dept. of mathematics, H.PU. shimla, India, 1993, pp. 43-53
[16] [16] Gupta, S.K. 'Elastic-plastic and creep transition of thick-walled cylinder under uniform pressure’, Proc. Of Int. Symp. On Non-linear Mech. Kharagpur, 1980, pp. 169-175
[17] [17] Odquist, F. K.G., Mathematical Theory of Creep and Creep Rupture, Clarendo Press, Oxford, 1974
[18] [18] Levitsky, M., Shaffer B. W., Residual Thermal Stresses in a Solid Sphere form a Thermosetting Material, Jr. of Appl. Mech., Trans. of ASME, 42(1975), 3, pp. 651-655
[19] [19] Gupta, S.K., Dharmani, R.L., Creep transition in thick walled cylinder under internal Pressure, Z.A.M.M. Mech., 59(1979), pp. 517-521
[20] [20] Pankaj, S. K. Gupta, Thermo Elastic-plastic transition in a thin rotating Disc with inclusion, Thermal Science, 11(2007), 1, pp. 103-118
[21] [21] Pankaj Thakur, Elastic-plastic transition stresses in rotating cylinder by finite deformation under steady-state temperature, Thermal Science International Scientific Journal, 15(2011), 2, pp. 537-543
[22] [22] Pankaj Thakur, Elastic-plastic transition stresses in a thin rotating disc with rigid inclusion by infinitesimal deformation under steady state Temperature, Thermal Science International Scientific Journal, 14(2010),1, pp. 209-219
[23] [23] Pankaj Thakur, Creep Transition Stresses in a thin rotating disc with shaft by finite deformation under steady state temperature, Thermal Science International Scientific Journal, 14(2010), 2, pp. 425-436
[24] [24] Pankaj Thakur, Creep transition stresses of a thick isotropic spherical shell by finite deformation under steady state of temperature and internal pressure, Thermal Science, 15(2011), Suppl. 2, pp. S157-S165
PDF VERSION [DOWNLOAD]
Steady thermal stress and strain rates in a circular cylinder with non-homogeneous compressibility subjected to thermal load

© 2026 Society of Thermal Engineers of Serbia. Published by the Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, Belgrade, Serbia. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International licence