THERMAL SCIENCE

International Scientific Journal

Hiba A. Hasan

,

Kadhim H. Suffer

,

Alyaa H. Akhbala

NUMERICAL SIMULATION OF USING NANOPARTICLES TO ENHANCE SOLAR THERMAL ENERGY STORAGE SYSTEM OF SHELL AND DIFFERENT SHAPE FINNED TUBES

ABSTRACT
Developing a latent heat storage system is crucial for enhancing the efficiency of heat that is absorbed from the sun to storing in the solar thermal energy storage system. In present study, numerical analysis using CFD with experimental validation is used to simulate the effect of geometrical shape (tube, nozzle, and reducer) rounded by fins with circular shape to enhance the latent heat storage of phase change material (PCM). In addition to analysis the effect of 2% and 5% of aluminum oxide nanoparticles to the PCM. The predicted results showed that the nozzle shape give the fastest melting time compared between the other shapes where the melting time decreased by 9.1% and 10.36% at a 5% and 2% concentration of aluminum oxide respectively, compared to the tube. In contrast, the results of using the tube compared to the reducer showed that the melting time decreased by 26.66% and 23.1% at a 5% and 2% concentration of aluminum oxide, respectively. Overall, the melting performance follows the order: nozzle, tube, and reducer, for both nanoparticle concentrations. Increasing the Al₂O₃ concentration enhances thermal responsiveness and shortens charging time, but the effectiveness of this enhancement depends strongly on the geometric configuration. Therefore, combining improved geometry with nano-optimization is a key design factor for enhancing the efficiency of latent thermal energy storage systems.
KEYWORDS
nanoparticles, latent heat, nozzle and reducer, Al2O3, circular fins
PAPER SUBMITTED: 2026-05-08
PAPER REVISED: 2026-06-24
PAPER ACCEPTED: 2026-06-29
PUBLISHED ONLINE: 2026-08-08
DOI REFERENCE: https://doi.org/10.2298/TSCI260508159H
REFERENCES (26)
[1] Alhamdo, M. H., et al., Finned Double-Tube PCM System as a Waste Heat Storage, IOP Conf. Series: Materials Science and Engineering, 95 (2015), 012033. 012033, 10.1088/1757-899X/95/1/012033
[2] Hasan, H. A., Hussain, I.Y., Experimental Investigation of Thermal Performance Enhancement of Cascade Thermal Energy Storage System by Using Metal Foam. International Journal of Mechanical Engineering Technology, 9 (2018), 9, pp. 1537-1549
[3] Pielichowska, K, Pielichowski, K., Phase Change Materials for Thermal Energy Storage, Progress in Materials Science, 65, (2014), pp. 67-123., 10.1016/j.pmatsci.2014.03.005
[4] Dzhonova-Atansova, D. B., et al., Numerical Study of Heat Transfer in Macro-Encapsulated Phase Change Material for Thermal Energy Storage, Bulgarian Chemical Communications, 48, Special Issue E (2016) pp. 189 - 194
[5] Khan, Z., et al., A Review of Performance Enhancement of PCM Based Latent Heat Storage System within the Context of Materials, Thermal Stability and Compatibility, Energy Conversion and Management 115C, (2016), pp. 132-158, 10.1016/j.enconman.2016.02.045
[6] Sharma A., et al., Review on Thermal Energy Storage with Phase Change Materials and Applications, Renewable and Sustainable Energy Reviews, 13 (2009), 2, pp. 318-345, 10.1016/j.rser.2007.10.005
[7] Joud, K. A., Taha, A. K., Simulation of Heat Storage and Heat Regeneration in Phase Change Material, Journal of Engineering, 18 (2012), pp. 1055-1072; doi.org/10.31026/j.eng.2012.09.06
[8] Wei, J., et al., Study on a PCM Heat Storage System for Rapid Heat Supply, Applied Thermal Engineering, 25, (2005), pp. 2903-2920, 10.1016/j.applthermaleng.2004.07.019
[9] Tao, Y. B., Carey, V. P., Effects of PCM Thermophysical Properties on Thermal Storage Performance of a Shell-and-Tube Latent Heat Storage Unit, Applied Energy, 179 (2016), pp. 203-210, 10.1016/j.apenergy.2016.05.097
[10] Hasan, H. A., Thermal Performance of Aluminum Oxide Nanoparticles-Enhanced Latent Thermal Storage Heat Exchanger of Spiral-Wired Tube, Arabian Journal for Science and Engineering, 50 (2024) 2265-2276
[11] Hussain, E. S., Hussain, I. Y., Numerical Study of Performance Enhancement of Phase Change Material Thermal Energy Storage System by Using Nanoparticles, Al-Nahrain Journal for Engineering Sciences, 28 (2025), 1, pp. 1-7
[12] Motahar, S., et al., Experimental Study on Solidification Process of a Phase Change Material Containing TiO2 Nanoparticles for Thermal Energy Storage, Energy Conversion and Management, 138 (2017), pp. 162-170, 10.1016/j.enconman.2017.01.067
[13] Mahdi, J. M., Nsofor, E. C., Solidification Enhancement of PCM in a Triplex-Tube Thermal Energy Storage System with Nanoparticles and Fins, Applied Energy, 211 (2018), pp. 975-986, 10.1016/j.apenergy.2017.11.053
[14] Al-Jethelah, et al., Charging Nanoparticle-Enhanced Bio-Based PCM in Open Cell Metallic Foams: An Experimental Investigation, Applied Thermal Engineering, 148 (2019), pp. 1029-1042, 10.1016/j.applthermaleng.2018.11.074
[15] Jegadheeswaran, S., Pohekar, S. D., Performance Enhancement in Latent Heat Thermal Storage System: A Review, Renewable and Sustainable Energy Reviews, 13 (2009), 9, pp. 2225-2244, 10.1016/j.rser.2009.06.024
[16] Abdulateef, A. M., et al., Geometric and Design Parameters of Fins Employed for Enhancing Thermal Energy Storage Systems: A Review, Renewable and Sustainable Energy Reviews, 82 (2018), pp. 1620-1635, 10.1016/j.rser.2017.07.022
[17] Hosseini, M. J., et al., Thermal Analysis of PCM Containing Heat Exchanger Enhanced with Normal Annular Fins, Mechanical Sciences, 6 (2015), 2, pp. 221-234, 10.5194/ms-6-221-2015
[18] Cheng, H., et al., Experimental Study of a Shell-and-Tube Phase Change Heat Exchanger Unit with and without Circular Fins, Energy Procedia, 152 (2018), pp. 990-996, 10.1016/j.egypro.2018.09.202
[19] Al-Ali, H., et al., Melting and Solidification of Phase Change Material in a Cylindrical Container with Y-Shaped Fins, Case Studies in Thermal Engineering, (2025), Article No. 106347, 10.1016/j.csite.2025.106347
[20] Hasan, H. A., Hassoon, A. S., Thermal Performance Investigation of Finned Latent Heat Storage of Shell-and-Tube, Shell-and-Nozzle, and Shell-and-Reducer Models, Heat Transfer, 52 (2023) pp. 4755-4773
[21] Jalil, J. M., Salih, S. M., Analysis of Thermal and Insulation Performance of Double Glazed Window Doped with Paraffin Wax, Engineering and Technology Journal, 38 (2020), Part A, 3, pp. 383-393
[22] Hasan, H. A., Suffer, K. H., Modeling of Shell and Various Tube Shapes with Annular Fins for Thermal Solar Energy Storage System, E3S Web of Conferences, 589 (2024), 10.1051/e3sconf/202458905004
[23] Hasan, H. A., Suffer, K. H., Thermal Performance Enhancement of Energy Storage System Using Spiral-Wired Tube Heat Exchanger, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 45 (2023), 3, pp. 7280-7293, 10.1080/15567036.2023.2220676
[24] Hasan, A. A., Jassim, N. A., Thermal Energy Shifting Using Thermal Energy Storage with Solar Assisted System for Space Cooling Application, Al-Nahrain Journal for Engineering Sciences, 23 (2020), 3, pp. 216-224, 10.29194/NJES.23030216
[25] Hasan, H. A., Hussain, I. Y., Simulation and Testing of Thermal Performance Enhancement for Cascade Thermal Energy Storage System by Using Metal Foam, International Journal of Mechanical and Mechatronics Engineering (IJMME-IJENS), 18, (2018), 5. Pp.106-117
[26] Jafar, M. H., Qussai, J. A., Mohammed, F. M., CFD Simulation of Enhancement Techniques in Flat Plate Solar Water Collectors, Al-Nahrain Journal for Engineering Sciences, 20 (2017), 3, pp. 751-761
PDF VERSION [DOWNLOAD]
Numerical simulation of using nanoparticles to enhance solar thermal energy storage system of shell and different shape finned tubes

© 2026 Society of Thermal Engineers of Serbia. Published by the Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, Belgrade, Serbia. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution 4.0 International licence